We are pleased to stock these amazingly compact boards from Big Al's. This version can be used with 2s to 6s battery configuration.
This board is silent unlike other PWM boards due the the switching frequency. It's so fast it's silent.

ATTENTION
These boards use a 1K potentiometer, not a 10K like other PWM boards.


Manufacturers Info:
Big Al's Lipo PWM board is a compact, high power PWM voltage regulator that is designed to fit snugly into a box along side a lipo battery. It can be used with Lipo batteries and regualar 18650s in either a 2s, 3s, 4s, 5s or 6s configuration.The board has an master on/off switch and a built-in 180A P-channel MOSFET.

Big Al's Lipo PWM board uses the same 555 circuit as Big Als PWM Sled board which is different from the standard 555-with-diodes that is used in practically every other board.   Big Al's Lipo board operates at 25 KHz, which improves the accuracy of external voltmeters, as well as eliminating any "Hum" that is present with other PWM boards.  

Big Al's Lipo PWM board requires no external components  other than the battery, the button and the 510 connector.  The pot is mounted directly onto the board, or it can be wired to the board and mounted somewhere else. 
 

Specs:
Maximum recommended operating current: 60A
P-MOSFET rated current: 180A
PWM frequency: 25 KHz
Standby Current draw: <10 µA
Built in On/Off switch - In the "On" position when the switch is pointing to the left, or closest to the edge of the PCB.
Output Adjustment  Range (approximate)
 2 cells - 1.9V to 100% of battery
 3 cells - 2.5V to 100% of battery
 4 cells - 2.9V to 100% of battery
 6 cells - 4.0V to 100% of battery   

Example power output at maximum rated current, different battery configurations:
 2 cells  -  440 Watts
 3 cells  -  660 Watts
 4 cells  -  880 Watts
 6 cells  -  1332 Watts  

Please note that there is no current limiting on this board.  Therefore, while it is possible to switch much higher currents than the recommended maximum current, this could seriously heat up the FET and ultimately damage it.
The reason the maximum recommended current is lower than the PFET maximum current is to provide a safety factor and also to prevent heat damage to the board and any wires soldered to it.  
 

Datasheet: Big Al's Side Mount 6S PWM Board Spec Sheet

Grove Trading / Big Al's Returns Policy
If you have problems with one of these boards that was not caused by you, please return it to us for a full refund or a replacement. Your refund or replacement will be sent on receipt of the board. Please include the Grove Trading invoice number with the returned board and send to our address:
Grove Trading, Kelly House, 1 Warwick Road, Tunbridge Wells. TN1 1YL. United Kingdom

Write a review

Please login or register to review

Big Al's Side Mount 6S PWM Board

  • £13.99

  • Ex Tax: £11.66

Related Products

1K Ohms Single Turn Trimming Potentiometer

1K Ohms Single Turn Trimming Potentiometer

Nice little 1K 1/2” Diameter Single Turn Cermet Trimming Potentiometer. Perfect for OKL2 builds.  ..

£2.99 Ex Tax: £2.49

Vishay P16 1K Ohm Potentiometer

Vishay P16 1K Ohm Potentiometer

The perfect potentiometer for OKL & Big Al's PWM builds Datasheet: Vishay P16 ..

£9.99 Ex Tax: £8.33

Big Al's Sled Mount 4S PWM Board

Big Al's Sled Mount 4S PWM Board

We are pleased to stock these amazingly compact boards from Big Al's. They can be used in 2s, 3s or ..

£12.99 Ex Tax: £10.83

Big Al's Sled Mount 4S iPWM Board

Big Al's Sled Mount 4S iPWM Board

Big Al's Intelligent PWM (iPWM) board has many of the features of the most advanced regulators at..

£14.99 Ex Tax: £12.49

Tags: Big, Al's, Silent, LiPo, PWM, Board