PLEASE READ CAREFULLY BEFORE PURCHASING
Big Al's PWM boards are not recommended for beginners. Please DO NOT buy this product if you expect a refund or replacement should the board not work for you after you have soldered it. This board comes in working condition and is fully tested by the manufacturer so please take care and accept responsibility for it should your build not work out.
We have a facebook group should you have problems and would like help identifying if it can be fixed but please have tools available like a multimeter so we can try to help you.
https://www.facebook.com/groups/ModMakingHelp/

We are pleased to stock these amazingly compact boards from Big Al's. They can be used in 2s, 3s or 4s battery configurations for massive power if needed making them extremely versatile.

One of the key features to me is they can fit onto the end of a KeyClone 1047 or Keystone 1047 holder simply by bending the tabs back and inserting them into the board in the slots provided. See in the images.


ATTENTION
 These boards use a 1K potentiometer, not a 10K like other PWM boards.

Manufacturers Info:
Big Al's PWM board is a compact, high power PWM voltage regulator that is designed to fit comfortably on top of any 2x18650 battery sled. It can also be used for Lipo batteries in either a 2s, 3s, or 4s configuration.   The board has an master on/off switch, reverse polarity protection, and a built-in 180A P-channel MOSFET. Big Al''s PWM board uses a dual 555 circuit, which is different from the standard 555-with-diodes that is used in practically every other board.   In this circuit, one 555 timer generates the square-wave output (at approximately 650 Hz) and the other 555 circuit generates the varying pulse length.  The advantage of this circuit over the diode circuit is that the board can be used with 2s, 3s, or 4s battery configurations, the frequency of the PWM does not change as the duty cycle is adjusted, and the pot can be connected using only two wires. Big Al''s PWM board requires no external components  other than the pot, button and the 510 connector.  It is also compatible with ModMaker''s Modmeter.  

More Info:

Datasheet: Big Al''s PWM Datasheet
Wiring Diagram: Big Al''s PWM Wiring Diagram
Parts List: Big Al''s PWM Board, 1K Potentiometer, KeyCLONE 1047, Any switch, any 510.

Big Al's Sled Mount 4S PWM Board

  • Brand: Big Al's Mods
  • Product Code: 425
  • Availability: Out Of Stock
  • £12.99

  • Ex Tax: £10.83

Related Products

1K Ohms Single Turn Trimming Potentiometer

1K Ohms Single Turn Trimming Potentiometer

Nice little 1K 1/2€ Diameter Single Turn Cermet Trimming Potentiometer. Perfect for OKL2 builds. ..

£2.99 Ex Tax: £2.49

Big Al's Side Mount 6S PWM Board

Big Al's Side Mount 6S PWM Board

PLEASE READ CAREFULLY BEFORE PURCHASINGBig Al's PWM boards are not recommended for beginners. Please..

£13.99 Ex Tax: £11.66

Big Al's Sled Mount 4S iPWM Board

Big Al's Sled Mount 4S iPWM Board

PLEASE READ CAREFULLY BEFORE PURCHASINGBig Al's PWM boards are not recommended for beginners. Please..

£14.99 Ex Tax: £12.49

KeyCLONE 1047 Dual 18650 Battery Holder

KeyCLONE 1047 Dual 18650 Battery Holder

Please Note: These are copies of the Keystone 1047 battery holder. Made by Blossom Electronics with..

£2.99 Ex Tax: £2.49

Big Al's Side Mount 6S iPWM Board

Big Al's Side Mount 6S iPWM Board

PLEASE READ CAREFULLY BEFORE PURCHASINGBig Al's PWM boards are not recommended for beginners. Please..

£14.99 Ex Tax: £12.49

Micro USB 2S Balance Charger

Micro USB 2S Balance Charger

We are pleased to finally bring you a USB charger capable of balance charging a 2 battery series mod..

£6.99 Ex Tax: £5.83

Big Al`s ANT 6S PWM Board

Big Al`s ANT 6S PWM Board

PLEASE READ CAREFULLY BEFORE PURCHASINGBig Al's PWM boards are not recommended for beginners. Please..

£13.99 Ex Tax: £11.66

Tags: Big, Al's, Sled, mount, 4S, PWM, Board